Category Archives: Cleaning Tips and Tools

How to Install Wall to Wall Carpet Yourself?

How to Install Wall to Wall Carpet YourselfAre you planning to lay a new carpet in your room all by yourself? If yes, you will find this article extremely useful. Here, we have discussed all the steps of installing a wall to wall carpet. Read through the discussion carefully and begin the installation job.

Step 1: You will need to begin by measuring the room. This step is important for determining how much carpet is required for covering the entire floor of the room. Measure the room’s length and width carefully. Don’t forget to add a few additional inches to both the room’s length and width for allowing extra carpet for doorways and thresholds.

Step 2: In the next step of the installation procedure, you will need to check for squeaks. Take out the shoe molding and carefully inspect the sub-floor for squeaks. If you locate any squeak, mark it with the letter “X”. Now, insert a medium-sized drywall screw into the room’s sub-floor on the marked area, down into its joist.

Step 3: This step involves installation of tack strips all across the room’s perimeter. When doing so, you will have to maintain a 3/8 inch gulley between the base-board and tack strip. Ideally, you should determine the exact distance by positioning your fingers between the tack strip and the wall. Experts say that the tack strips used for this purpose should be wide.

Step 4: In this step, you will need to lay out the carpet cushion. You must always buy a high quality carpet cushion; this is important for protecting both your feet and the carpet. The laying job should begin from any one corner of the room. Starting from a corner, you should roll out the entire strip carefully so that there’s no visible gap after carpet installation. Don’t miss giving the space a clean look by making relief cuts wherever necessary. Finally, thoroughly staple the carpet cushion down at every 2 ft or so.

Step 5: This step is about rolling out and fitting the carpet, which make it the most important step of this installation process. You will need help from another adult member of your family to bring the carpet roll to the room as usually these rolls are extremely heavy. Roll the carpet out and place it properly on the floor; there should be enough excess on the walls.

For finding out whether the carpet edges are parallel to their corresponding walls, use a knitting needle to draw a line across the tuft adjacent to the base-board. Make a horizontal cut and a couple of vertical cuts along that line; this will form a window. Repeat all these steps till the wall’s far end. If required, use a knee kicker for adjusting the carpet so that it is flush to the base-board.

Step 6: You are now ready to begin carpet installation. Installation should be started from any corner of the room. After every 5 inch or so, place a nail and hammer it onto the carpet. This will allow the carpet to stay in place permanently.

Step 7: While trimming the carpet along the wall, tack it down into the space between the base-board and tack strip; the term used for this part is “gulley”. For doing this job, you will need a plastic paddle.

Step 8: Once the carpet is installed, get the shoe molding replaced and vacuum the surface well.

These were the few steps that make up the carpet installation procedure. If the steps appeared to be too complex, you can hire professionals to do the job for you. For that, you will have to get in touch with a company offering carpet installation and cleaning service.

Tips and Tricks for Easy Carpet Stain Removal

Tips and Tricks for Easy Carpet Stain Removal

While some may say stain removing from a carpet falls under the easy task category, don’t get your hopes up a bit! The reality is quite the opposite. There is no easy way out of this, as removing stains from carpets are as hard as a task can get. What makes it harder is that removing stains, no matter what type it may be, is devilishly tricky. However, if you can get few tricks right and get the proper tips going your way, then you probably won’t have to suffer in the long run with your carpets. This article mainly focuses on some of the common tips and tricks that you should always keep in your mind so that you can implement them in a proper way.

Remember the Basics

Before starting the procedure for removing stain from your carpet, you should always remember the basics. In most cases, if you get the basics right, then the rest of the work becomes much easier. When you are removing the stain, just do the simplest thing – blot the stained spot and dry it from the outside in. Then start rinsing it thoroughly using clean water. After a while blot it again. Remember, never scrub the carpet during this, as it will risk destroying fibre of the carpet.

Test on a Clean Area First

When you are ready to start removing stain off the carpet, you should at first go for the testing phase. Get ready to apply your desired method on the carpet’s inconspicuous spot for better safety. In this case, even if it goes wrong, your carpet won’t be ruined as it won’t discolour the carpet. And in case even if it does, then it will remain quite unnoticeable because of the spot that you chose.

Removing Water-soluble stain

The easiest way to remove water-soluble stain is to get a cleaning solution. You can do it yourself mixing it with water. The usual levels of mixture would be ¼ teaspoon size detergent (non-bleach type) with water volume of 32 ounces. This will do the trick.

Removing Special Water-soluble stain

Special water-soluble stain include stains created with blood, tea, vomit, coffee, etc. These are a bit harder to remove than the usual water-soluble stains. However, if you try with just 01 tablespoon ammonia along with just a cup of water duly mixed in, then it is most likely to work.

Removing Glue and Cigarette Burns

When it comes to removing stains created by the glue and cigarette burns, then you got to be a bit tricky. With the glue thing, you should apply some alcohol with the help of a soft cloth first. Then wait for total moistened condition of the selected area, and start wiping it off. That’s it. In case of cigarette burns, you can just gently rub the pile with the help of a dull knife or a similar material, then you will get your result in no time!

The final trick and tip to easy stain removal is not letting your carpet go without maintenance for longer than it should be. Get your carpet cleaned thoroughly in every 12 to 18 months for maintaining the best condition of the carpet, which will also make it easier for cleaning the stain off it when the time comes. The reason behind it is that with proper and regular, thorough cleaning, the carpet fibres remain soft and therefore, easily washable.